bumper sink in
+15
Brainstain
BicknellWelding
Buzzman
Cdub74
coreys73chevelle
The Dude
BlackChevelleSS
bigredlaguna
McCauley5983
Hydro King
JB2wheeler
novaderrik
jonny o
Limey SE
Oidar
19 posters
Page 3 of 3 • 1, 2, 3
Re: bumper sink in
Stock 1973 Chevelle front end. From the looks of your avatar, you have a Laguna. Surely someone on here would be willing to trade. I almost would just to have a Laguna front for back up. Basically to answer your question though, all Chevelles came with the chrome bumpers except Laguna models which had the urethane front end like yours. There have been a few different methods for sinking in the bumper, check out the sticky in the body section.
The Dude- Management
- Street Cred : 48
Re: bumper sink in
BlackChevelleSS wrote:well we got the bumper sunk in without any fabrication we just used the factory brackets and didnt even mess with the shocks and it turned out great. I dont have pics of all what we did but I could type it up if anyones interested.
I miss that car
___________________________________________
www.cardomain.com/id/3115ultima
BlackChevelleSS- Management
- Street Cred : 20
Re: bumper sink in
The bad part is that it's just down the road in Claremore & the current owner is a member here. He signs in & looks around, but has never posted or kept us up to date on it.
The Dude- Management
- Street Cred : 48
Re: bumper sink in
my god that looks good even today. sunken bumper malibus are
coreys73chevelle- G3GM Senior Member
- Street Cred : 8
Re: bumper sink in
-Thanks Rago, my avatar pic is my car. Im going to keep the stock front end after a swap it out. But if anyone has a front end with a chome bumper, in great shape let me know!!!Rago wrote:Stock 1973 Chevelle front end. From the looks of your avatar, you have a Laguna. Surely someone on here would be willing to trade. I almost would just to have a Laguna front for back up. Basically to answer your question though, all Chevelles came with the chrome bumpers except Laguna models which had the urethane front end like yours. There have been a few different methods for sinking in the bumper, check out the sticky in the body section.
Cdub74- G3GM Member
- Street Cred : 0
RE: Bumper sink-in
I've gotta do this to my '73
Anybody have a more detailed description (with pics) on having this done? Step-by-step?
I have both the front and rear bumpers off now.
Anybody have a more detailed description (with pics) on having this done? Step-by-step?
I have both the front and rear bumpers off now.
Buzzman- G3GM Newbie
- Street Cred : 0
Re: bumper sink in
I've done this on my car, there is basically 2 chambers, one full of oil, then another one full of air. Also, after I drilled the 1 hole I went the the other end and drilled another to allow air to help release the air and oil. Then used a mallet to beat the shock where I wanted it to be. On both my cars front and rear, fully compressed is what I ended up doin. No ones wants to get into a collision, but I promise you, those absorbers aren't go to make any difference empty or full, they were only rated for impacts of less than 5 mph if I remember correctly. We all know an impact of 35 mph or better, alot of damage will be a given, those "shocks" wont help much then.
Bruisr- G3GM Member
- Street Cred : 8
Re: bumper sink in
I've done this mod to my 74 chevelle and to 2 76 el caminos. And any other G-3 I get in the future!
Bruisr- G3GM Member
- Street Cred : 8
front bumper
https://i.servimg.com/u/f10/18/05/88/16/th/fornt_21.jpg[/img][/url][/img][img][/img][img][/img]
Last edited by Bruisr on Sat Jan 19, 2013 1:18 am; edited 2 times in total
Bruisr- G3GM Member
- Street Cred : 8
Re: bumper sink in
love it ... plan on doing it to mine ... let's just hope we don't run into anything
alleyball4- Donating Member
- Street Cred : 5
Re: bumper sink in
Bruisr wrote:[img][/img][img][/img][img][/img]
Looks great!
How hard was the rear & how the heck did you get the sides that tight against the body?
77mali- Donating Member
- Street Cred : 62
Re: bumper sink in
Looks great, and really well executed. How much did you need to section out to get the sides in? This is on my list of to do's for "Ethel".
BicknellWelding- Donating Member
- Street Cred : 3
Re: bumper sink in
The bumper looks way different than my 77...what's the spacing of the bolt holes on yours?
77mali- Donating Member
- Street Cred : 62
Re: bumper sink in
74-5 are different than the 76-77. Later years are much bigger and boxier.
Brainstain- Donating Member
- Street Cred : 8
Re: bumper sink in
I took the bumper off the car removed the inner support, only enough to remount to rebound shocks.( not gonna see alot of street use, if so OWELL!) I found a relatively straight piece to mark my cut. Purposely where the bumper jack slot is. I cut the curved corner completely off. Reinstalled bumper(temporarily, where I wanted it positioned) I then took the cut pieces and slid them inside the place where I cut them at. Behind the cut end kinda inside the bumper. I then measured and marked with masking tape and trimmed off approx.1.5 inches from both sides. This got a little tricky, I enlarged the 4 slots that the rebound shocks mount to inner bumper to allow for slight adjustments. Ensuring bumper is centered on car, side to side. I tacked welded the corners back on to trial fit. Several times. Even trimming on the far bottom inside edge where bumper is closest to bottom of quarter panel. After I was satisfied I finished welding, then ground down welds. I have some cleaning up to do yet, but I'm still working on other mods.
Bruisr- G3GM Member
- Street Cred : 8
Re: bumper sink in
The bolt spacing on is 11 inches for the 1 on each corner, the rest are 14 inches. Also I needed to trim the section in front of the flip up license plate, I removed about 1/2 wide by whatever the width of the plate is, to get to fuel neck.[img][/img]
Bruisr- G3GM Member
- Street Cred : 8
Re: bumper sink in
Thanks, I'll compare mine as well...won't be doing this for a while yet. Hope I can use my filler too. I don't think I'll go as close in but do want to tuck the sides in as close as I can.
77mali- Donating Member
- Street Cred : 62
Re: bumper sink in
That looks really nice. That's exactly what I've wanted to do since i tucked my bumpers 12 years ago. Are you gonna have the bumper rechromed or paint it?
dynchel- Donating Member
- Street Cred : 40
Re: bumper sink in
I plan to paint them body color, but that is yrs.down the road. Although I'm undecided on color. Right now I'm contemplating on removing the bolts that can be seen, and filling them in. Not yet figured out how to do this. I've seen it done on Stacy's "trucks" program on TV but don't remember what episode.
Bruisr- G3GM Member
- Street Cred : 8
Re: bumper sink in
when I took my bumper to the chrome shop, he asked if I wanted him to fill in the bumper bolt holes. It sounds like they just weld up the holes, grind it flush, and chrome or paint over it.
I haven't rechromed my bumper yet, but I agree with you; I do like the look with no bumper bolts.
I haven't rechromed my bumper yet, but I agree with you; I do like the look with no bumper bolts.
alleyball4- Donating Member
- Street Cred : 5
Re: bumper sink in
The process is to grind the round heads off the carriage bolts and weld them in, ( the square part) then the outside is smoothed and rechromed. The bolts have to be there to hold the chrome piece to the internal brace.alleyball4 wrote:when I took my bumper to the chrome shop, he asked if I wanted him to fill in the bumper bolt holes. It sounds like they just weld up the holes, grind it flush, and chrome or paint over it.
I haven't rechromed my bumper yet, but I agree with you; I do like the look with no bumper bolts.
dynchel- Donating Member
- Street Cred : 40
dynchel- Donating Member
- Street Cred : 40
Page 3 of 3 • 1, 2, 3
Permissions in this forum:
You cannot reply to topics in this forum
Thu Dec 05, 2024 10:41 am by zucchi
» I have posted on here for info and help
Thu Dec 05, 2024 12:11 am by muldokken
» Roll Call and Car showcase
Fri Nov 29, 2024 5:24 pm by 76Chevelle2Tone
» Happy Thanksgiving 2024
Thu Nov 28, 2024 12:21 pm by Limey SE
» Life & Back On The Radio
Thu Nov 28, 2024 1:46 am by knightfan26917
» Monte Carlo -75
Wed Nov 27, 2024 12:57 pm by Finn Monte
» 1974 Pontiac Grand Prix
Mon Nov 25, 2024 5:06 pm by Iggy
» Ads
Mon Nov 25, 2024 12:52 am by 76Chevelle2Tone
» 1975 El Camino - long term project
Sun Nov 24, 2024 8:33 pm by tgaetto
» station wagon tailgate release
Sat Nov 23, 2024 8:28 pm by bucket