OK GUYS/ GALS
+2
itis34
BlackChevelleSS
6 posters
G3GM :: G3 :: General Discussion
Page 1 of 1
OK GUYS/ GALS
by Limey SE Tue May 10, 2011 6:26 pm
I forgot to mark the right drive shaft ( have 3 in garage ) and I forgot to mark the right one for the BU can some one measure theres for me thanks !!!!!!!!
oh 350th is the trans
oh 350th is the trans
___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE- Management
- Street Cred : 98
Re: OK GUYS/ GALS
by Limey SE Tue May 10, 2011 9:54 pm
NO ONE has there drive shaft out LOL
___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE- Management
- Street Cred : 98
Re: OK GUYS/ GALS
by BlackChevelleSS Tue May 10, 2011 10:13 pm
gonna go out on a limb and say 55 inches but its a guess.
___________________________________________
www.cardomain.com/id/3115ultima
BlackChevelleSS- Management
- Street Cred : 20
Re: OK GUYS/ GALS
by Limey SE Tue May 10, 2011 10:29 pm
from end to end or u joint to u joint
___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE- Management
- Street Cred : 98
Re: OK GUYS/ GALS
by itis34 Wed May 11, 2011 7:39 am
I'm trying to get a driveshaft set up for my 77 Cutlass right now. Best I can do for you is, it originally had a 400 and the shaft was 53". I am putting a 700R4 in it and I'm measuring that at 50 3/4". Dimensions are centerline to centerline of the u-joint.
itis34- G3GM Newbie
- Street Cred : 0
Re: OK GUYS/ GALS
by Limey SE Wed May 11, 2011 12:19 pm
thank you everyone I was able to get the one Back from the Cutlass so gonna try that one first !!!
___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE- Management
- Street Cred : 98
Re: OK GUYS/ GALS
by oldstofty Wed May 11, 2011 2:28 pm
51 inches for a th400 long tail if your trying to narrow it down
oldstofty- G3GM Member
- Street Cred : 7
Re: OK GUYS/ GALS
by 1973 454 MONTE Wed May 11, 2011 3:37 pm
Limey wrote:from end to end or u joint to u joint
i would measure mine but CJ my 16 yo has the monte today
1973 454 MONTE- Donating Member
- Street Cred : 36
Re: OK GUYS/ GALS
by Limey SE Wed May 11, 2011 3:40 pm
1973 454 MONTE wrote:Limey wrote:from end to end or u joint to u joint
i would measure mine but CJ my 16 yo has the monte today
OH I bet he is in 7th heaven right now Buddy driving that car, Can almost smell the rubber from here LOL
___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE- Management
- Street Cred : 98
Re: OK GUYS/ GALS
by Marshall.Pixley Wed May 11, 2011 8:57 pm
i would measure mine but of course i drive an elco, and it a bit longer
Marshall.Pixley- G3GM Member
- Street Cred : 0
Similar topicsG3GM :: G3 :: General Discussion
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum|
|
|
» Roll Call and Car showcase
» Central Texas Noob
» Welcome Keith Seymore
» Wanted: Front park lamp assemblies
» 75 Hurst Olds T-tpos
» G3 Chevy rims- help ID these
» 75 el camino project.
» Have had a few questions
» vinyl top removal