10 bolt proper positraction application?
4 posters
G3GM :: G3 Tech :: Engine & Driveline
Page 1 of 1
10 bolt proper positraction application?
I have a stock 10 bolt rear with non-posi 2.73 gears, looking at 4.11 posi for it, who would be the best to get it from and what do i need? they show 28spline and 30spline and so on but i dont know what i have or how to find out. was thinking of getting Eaton LSD are they good for our cars?
coreys73chevelle- G3GM Senior Member
- Street Cred : 8
Re: 10 bolt proper positraction application?
this will be a steet/strip car. if i have a th350 and a 400hp 355 whats my top speed? with 4.11 and with 3.73 with 295/50s rear
coreys73chevelle- G3GM Senior Member
- Street Cred : 8
Re: 10 bolt proper positraction application?
You have 28 spline axles. Eatons are good.
ant7377- G3GM Addict
- Street Cred : 36
Re: 10 bolt proper positraction application?
The rearend in a 73-77 a body uses a 8.5 inch ring gear and 28 spline axles.
If your looking for a used posi carrier
A 2nd gen camaro/ firebird uses a 8.5 carrier also 72 up novas.
Just make sure that it's a 3 series carrier. (2.73 and up gear ratio).
In my personal opinion i would go with a 3.73 gear ratio if your using a 295/50/15 tire because the tire is real short and the 4.11's will suck for street driving especially on the highway.
I now there's alot more factors in picking the right gear ratio for your engine/trans combo but if the car is going to see more street use then strip i would go with 3.73.
If your looking for a used posi carrier
A 2nd gen camaro/ firebird uses a 8.5 carrier also 72 up novas.
Just make sure that it's a 3 series carrier. (2.73 and up gear ratio).
In my personal opinion i would go with a 3.73 gear ratio if your using a 295/50/15 tire because the tire is real short and the 4.11's will suck for street driving especially on the highway.
I now there's alot more factors in picking the right gear ratio for your engine/trans combo but if the car is going to see more street use then strip i would go with 3.73.
G3NUT- Donating Member
- Street Cred : 11
Re: 10 bolt proper positraction application?
coreys73chevelle wrote:this will be a steet/strip car. if i have a th350 and a 400hp 355 whats my top speed? with 4.11 and with 3.73 with 295/50s rear
Try this http://www.wallaceracing.com/gear-speed.php
alowerlevel- G3GM Member
- Street Cred : 6
Similar topics
» What rearend with positraction should i look for
» proper screws for 73 ss courtesy lamps?
» proper re-install technique 73 SS front bumper?
» proper screws for 73 ss courtesy lamps?
» proper re-install technique 73 SS front bumper?
G3GM :: G3 Tech :: Engine & Driveline
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
Yesterday at 10:59 pm by 76Chevelle2Tone
» 14 Month Battle / Search is over
Yesterday at 10:36 pm by g3chevy / Mr Pontiac
» vinyl top removal
Mon Nov 11, 2024 2:49 am by 76Chevelle2Tone
» Limeys Shirt House yes its me Doing a Sale on Custom Shirts
Sun Nov 10, 2024 4:29 pm by 76Chevelle2Tone
» broken console base
Sun Nov 10, 2024 1:31 pm by 454fourspeedss
» 2025 Calendar I know Late start LOL
Sat Nov 09, 2024 12:50 pm by Limey SE
» Where to find 1973 Grand Am Part Numbers?
Fri Nov 08, 2024 9:10 pm by 76Chevelle2Tone
» Roll Call and Car showcase
Fri Nov 08, 2024 7:31 am by Dinomyte
» 75 el camino project.
Sun Nov 03, 2024 12:05 am by tgaetto
» Chevelle Power Trunk Release
Fri Nov 01, 2024 12:58 pm by Keith Seymore