PS Bracket Diagrams or Photos
3 posters
Page 1 of 1
PS Bracket Diagrams or Photos
I am putting my PS pump and brackets back together and need some help. I have it mostly figured it out how it goes together, but I have small spacer that I can't remember where it goes. I took some pics but apparently not enough.
Does anyone have a factory diagram or some pics of how these brackets are assembled? Does anyone remember as small spacer?
Does anyone have a factory diagram or some pics of how these brackets are assembled? Does anyone remember as small spacer?
76 Malibu- G3GM Member
- Street Cred : 2
the parts manual has a parts breakout of the ps pump mount
I'm far from the most knowledgeable here. I only see one spacer (assume you don't mean washers) which was used with the mounting bracket, the one with the long thin curved space. Hope that helps. If not maybe someone else will chime in.
76Chevelle2Tone- G3GM Member
- Street Cred : 0
Re: PS Bracket Diagrams or Photos
76Chevelle2Tone wrote:I'm far from the most knowledgeable here. I only see one spacer (assume you don't mean washers) which was used with the mounting bracket, the one with the long thin curved space. Hope that helps. If not maybe someone else will chime in.
I only have one spacer, so that is probably correct. Can you snap a pic by chance of where it goes?
76 Malibu- G3GM Member
- Street Cred : 2
my image provider doesn't work here
Looking at the parts manual, if you are standing in front of the car the spacer goes behind the left hand hex bolt hole on the bottom of the bracket. A washer goes in front and the 3/8 inch hex bolt pins both.
76Chevelle2Tone- G3GM Member
- Street Cred : 0
76 Malibu- G3GM Member
- Street Cred : 2
76Chevelle2Tone likes this post
glad you got it fixed
Just to recap for others:
In the Chevy Parts Illustration Manual 1976-81 p. 6-47 (A,B,F,X 8 Cyl Engine Power Steering Pump Mounting). There is an undocumented spacer that fits behind Bracket 21 aka steering pump pivot because of the longer bolt as 76 Malibu noted. The only documented spacer fits behind Bracket 18 aka Front Support. A washer goes in front of the bracket and the spacer behind the bracket in both cases. If removing the power steering pump, make sure you don't lose the Bracket 21 spacer because the manual will not help you haha.
In the Chevy Parts Illustration Manual 1976-81 p. 6-47 (A,B,F,X 8 Cyl Engine Power Steering Pump Mounting). There is an undocumented spacer that fits behind Bracket 21 aka steering pump pivot because of the longer bolt as 76 Malibu noted. The only documented spacer fits behind Bracket 18 aka Front Support. A washer goes in front of the bracket and the spacer behind the bracket in both cases. If removing the power steering pump, make sure you don't lose the Bracket 21 spacer because the manual will not help you haha.
76Chevelle2Tone- G3GM Member
- Street Cred : 0
Re: PS Bracket Diagrams or Photos
___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE- Management
- Street Cred : 98
Similar topics
» 2009 Oldsmobile Homecoming Photos (lots of photos, be warned)
» Where from factory is the stereo radio heat sink mounted and how????
» Rear Sway Bar Bracket
» Where from factory is the stereo radio heat sink mounted and how????
» Rear Sway Bar Bracket
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
Fri Nov 29, 2024 5:24 pm by 76Chevelle2Tone
» Need radio help
Thu Nov 28, 2024 10:48 pm by 76Chevelle2Tone
» Happy Thanksgiving 2024
Thu Nov 28, 2024 12:21 pm by Limey SE
» Life & Back On The Radio
Thu Nov 28, 2024 1:46 am by knightfan26917
» Monte Carlo -75
Wed Nov 27, 2024 12:57 pm by Finn Monte
» 1974 Pontiac Grand Prix
Mon Nov 25, 2024 5:06 pm by Iggy
» Ads
Mon Nov 25, 2024 12:52 am by 76Chevelle2Tone
» 1975 El Camino - long term project
Sun Nov 24, 2024 8:33 pm by tgaetto
» station wagon tailgate release
Sat Nov 23, 2024 8:28 pm by bucket
» 14 Month Battle / Search is over
Sat Nov 23, 2024 7:19 pm by 76 Malibu