Fuel injection
4 posters
G3GM :: G3 Tech :: Engine & Driveline
Page 1 of 1
Fuel injection
thinking about injecting my 76 now i have a 350 .040 over 4 bolt block my question is this....
Should i build that block and buy like a holley or edelbrock injeciton kit?
should i buy an LS type motor or LT motor and drop that in wiring harness and pcm?
or would it be easier to pickup a fuel injection setup heads and all off of a vortec 350 in say a suburban or truck out of a yard ?
any ideas form any one here would be helpful im aware that i would need the an electric fuel pump new lines and possibily a new tank with a return provision. but other than that ive never converted a vehicle before.
and then the last option is go E85 on the carb but scarcity of E85 stations near me and price of that carb is what kind aboots that out but in comparision i guess its cheaper than a FI kit ...
Should i build that block and buy like a holley or edelbrock injeciton kit?
should i buy an LS type motor or LT motor and drop that in wiring harness and pcm?
or would it be easier to pickup a fuel injection setup heads and all off of a vortec 350 in say a suburban or truck out of a yard ?
any ideas form any one here would be helpful im aware that i would need the an electric fuel pump new lines and possibily a new tank with a return provision. but other than that ive never converted a vehicle before.
and then the last option is go E85 on the carb but scarcity of E85 stations near me and price of that carb is what kind aboots that out but in comparision i guess its cheaper than a FI kit ...
Redsway76- G3GM Member
- Street Cred : 0
Re: Fuel injection
If you got the money, GMPP is bringing out a series of LS crate motor kits which include EVERYTHING you need from the motor to the exhaust system and they are reasonably priced to boot. Notice I did not say cheap, I said reasonably priced. JB
JB2wheeler- G3GM Fanatic
- Street Cred : 28
Re: Fuel injection
If you just wanna stick with what you have, several companies now offer fuel injection kits that seem to work pretty well. The common setup is like a TBI setup. Instead of having to run return fuel lines, however, some of them use an electronic fuel pump that delivers the proper amount of fuel without needing a return line. If I can find any stuff on it I'll post it.
IndyG3- G3GM Enthusiast
- Street Cred : 11
Re: Fuel injection
Check out this swap we did on the kid's car. We used the 265 c.i. engine, not the 350, but everything applies. We also used the plastic fuel tank from the Caprice (bolts right in) and the Caprice donated the fuel supply line (Malibu line used for return). The 350 LT-1 was in the GM rear-drive big cars from the same years (93-96) so you could find a Caddy with the same driveline that will probably be in much better condition than a Chevy.
http://www.cardomain.com/ride/184268
http://www.cardomain.com/ride/184268
gcmarchi- G3GM Newbie
- Street Cred : 0
G3GM :: G3 Tech :: Engine & Driveline
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|
Today at 11:58 am by Keith Seymore
» Roll Call and Car showcase
Today at 9:20 am by g3chevy / Mr Pontiac
» Central Texas Noob
Today at 9:16 am by g3chevy / Mr Pontiac
» Welcome Keith Seymore
Today at 9:03 am by g3chevy / Mr Pontiac
» Wanted: Front park lamp assemblies
Today at 8:57 am by g3chevy / Mr Pontiac
» 75 Hurst Olds T-tpos
Today at 8:44 am by g3chevy / Mr Pontiac
» G3 Chevy rims- help ID these
Tue Oct 29, 2024 7:26 pm by Limey SE
» 75 el camino project.
Mon Oct 28, 2024 11:03 am by zucchi
» Have had a few questions
Sun Oct 27, 2024 11:04 am by Limey SE
» vinyl top removal
Sat Oct 26, 2024 10:30 pm by 76Chevelle2Tone