interior parts
+3
Sinister
jerry46765
1973 454 MONTE
7 posters
Page 2 of 2 • 1, 2
Re: interior parts
I've found a few minor things different between 76 and 77s. The lower dash doesn't have the clip for the speedo cable, instead it goes to a different style speedo head with the clip on it. A/C system is different, otherwise I've not found much to be different between the two. Oh the dome light is plastic instead of pot-metal. The obvious grill and taillights.
I'm thinking about re-doing my front seat, to get it ready for Powertour '13 its very much done for, and I've got a 76 GMC Sprint front seat ready to swap all the good parts (maybe) and just took the parts 77's rusty front seat apart to learn how to do it.
Looks like the backrest foam is interchangable? If so, my drivers side foam is so hashed that its not worth trying to reuse it.
I'm thinking about re-doing my front seat, to get it ready for Powertour '13 its very much done for, and I've got a 76 GMC Sprint front seat ready to swap all the good parts (maybe) and just took the parts 77's rusty front seat apart to learn how to do it.
Looks like the backrest foam is interchangable? If so, my drivers side foam is so hashed that its not worth trying to reuse it.
texan01- G3GM Member
- Street Cred : 6
Re: interior parts
You might have to find a back rest in a salvage yard. I haven't seen any replacement foam for the '73-'77s.....
pila- Donating Member
- Street Cred : 43
Re: interior parts
pila wrote:You might have to find a back rest in a salvage yard. I haven't seen any replacement foam for the '73-'77s.....
I haven't either, except for the 68-72 bench style with no armrest. Hence why I had 2 extra front seats. now I'm down to one extra front seat as the parts car I bought had the seat frame completely rusted out; not much was really usable from the interior anyway. Mine is just bent from someone large pushing the seatbacks back, and the springs on the drivers side are done, along with the foam.
texan01- G3GM Member
- Street Cred : 6
Re: interior parts
77mali wrote:It's funny how these company's that list all this stuff for the 73-77 GM cars don't even know what they're selling half the time. Take the dash cap I bought recently...wrong grain, terrible fit around the a/c vents, did not even "reach" the defroster vents when it's supposed to rest against the windshield...(about an inch too short in the middle)...I hate paying hard earned money for something and it's either totally wrong or a vendor won't admit it's not correct and try & blame you (car related especially).
Like the hood-to-cowl seal I bought from Metro that was 3 inches too short.
thatfnthing- Donating Member
- Street Cred : 65
Re: interior parts
thatfnthing wrote:77mali wrote:It's funny how these company's that list all this stuff for the 73-77 GM cars don't even know what they're selling half the time. Take the dash cap I bought recently...wrong grain, terrible fit around the a/c vents, did not even "reach" the defroster vents when it's supposed to rest against the windshield...(about an inch too short in the middle)...I hate paying hard earned money for something and it's either totally wrong or a vendor won't admit it's not correct and try & blame you (car related especially).
Like the hood-to-cowl seal I bought from Metro that was 3 inches too short.
3" is a lot to be off. Did they offer you a refund/exchange? I bet they packed it wrong- from what I understand they have a lot of returns & either repackage or "Fire sale" opened items to their dealer/resale network for them to re-package.
77mali- Donating Member
- Street Cred : 62
Re: interior parts
Tomorrow I'm gonna install the AC plastic ducts under the dash if I can remember how it all goes back together.
Also I want to design & fabricate strips to hold the carpet edge along the rear edge where it meets the back wall. Not sure what to use for those yet, but maybe aluminum, since I have lots of that. The carpet doesn't lay in there very good.
The red naugahyde covers the original charcoal colored insulator on the back wall panel, which was always an un-finished look. It has a pocket in it on the driver's side.
Also I want to design & fabricate strips to hold the carpet edge along the rear edge where it meets the back wall. Not sure what to use for those yet, but maybe aluminum, since I have lots of that. The carpet doesn't lay in there very good.
The red naugahyde covers the original charcoal colored insulator on the back wall panel, which was always an un-finished look. It has a pocket in it on the driver's side.
pila- Donating Member
- Street Cred : 43
Re: interior parts
77mali wrote:3" is a lot to be off. Did they offer you a refund/exchange? I bet they packed it wrong- from what I understand they have a lot of returns & either repackage or "Fire sale" opened items to their dealer/resale network for them to re-package.
I purchased it and it sat around for a while before I got that far -- had to seal up the inside of the cowl after the A/C project -- so by the time I discovered it it was way too late to go back and complain. I just made do. It's short on the driver's side, maybe I'll purchase another at some point and redo it.
thatfnthing- Donating Member
- Street Cred : 65
Page 2 of 2 • 1, 2
Similar topics
» Interior Trim parts
» '75 Chevelle station wagon project
» WTB: 73-77 Grand Prix Interior Parts Seat Tracks Seat Belts
» '75 Chevelle station wagon project
» WTB: 73-77 Grand Prix Interior Parts Seat Tracks Seat Belts
Permissions in this forum:
You cannot reply to topics in this forum
Today at 2:15 pm by jpowen49
» 14 Month Battle / Search is over
Yesterday at 11:06 am by Iggy
» vinyl top removal
Yesterday at 2:49 am by 76Chevelle2Tone
» Limeys Shirt House yes its me Doing a Sale on Custom Shirts
Sun Nov 10, 2024 4:29 pm by 76Chevelle2Tone
» broken console base
Sun Nov 10, 2024 1:31 pm by 454fourspeedss
» 2025 Calendar I know Late start LOL
Sat Nov 09, 2024 12:50 pm by Limey SE
» Where to find 1973 Grand Am Part Numbers?
Fri Nov 08, 2024 9:10 pm by 76Chevelle2Tone
» Roll Call and Car showcase
Fri Nov 08, 2024 7:31 am by Dinomyte
» 75 el camino project.
Sun Nov 03, 2024 12:05 am by tgaetto
» Chevelle Power Trunk Release
Fri Nov 01, 2024 12:58 pm by Keith Seymore