Rubber parts conditioner
3 posters
Rubber parts conditioner
I didnt want to hijack the 1973 dash on ebay thread. Figured I'd post my experiences with a rubber parts conditioner. Dont know if it would work on the dash pad but I'm thinking of giving it a shot.
When I started my build and removed all the rubber seals I got to thinking. Why isnt there something to treat these parts to prolong their life. I started googling an found that alot of people are using Sil-glide. Its used on alot of things but especially brake caliper parts and especially the slides. People were saying that they clean the part, work this stuff into the part and let it sit. Then clean off the part. Its supposed to revive the parts and make them more pliable.
I went out and bought a tube for 8 bucks. Used it on my in-laws brake job and it worked well. I then put it on my rear axle rebound bumpers and rocker drain flaps in front of the rear wheels. All these parts were off the vehicle already. I cleaned the parts and then worked the Sil-glide into the part and left extra on it. Then I put the parts in a small zip lock back and let it sit a couple days. Went back to them, work the stuff into the parts some more and let it sit. Well after a couple of days I removed the part, wiped it clean and it looked good as new. I have to say it was a little more pliable than when I started. Not that the rebound bumpers are that pliable to begin with. But the rocker drain flaps were much better.
I've seen other guys using Sil-glide on there trunk and door weather stripping. I'll be trying that next during assembly.
This has me thinking about doing my dash pad.
Just thought I'd post up my findings with this stuff. Heres a link at advance auto. I know napa carries it too.
http://shop.advanceautoparts.com/p/american-grease-stick-co.-sil-glyde-silicone-brake-lubricant-tube-4-oz-bk-4/12024852-p?iv_=__iv_p_1_a_214327102_g_12425515822_w_pla-191564126422_h_9004189_ii__d_c_v__n_g_x_pla_y_6201684_f_online_o_12024852-P_z_US_i_en_j_191564126422_s__vi__&utm_source=ACQ&utm_medium=cpc&utm_campaign=PLA&utm_content=shoppingcampaigns&gclid=CJz_4IXswdACFQlXDQodj-cMrA
When I started my build and removed all the rubber seals I got to thinking. Why isnt there something to treat these parts to prolong their life. I started googling an found that alot of people are using Sil-glide. Its used on alot of things but especially brake caliper parts and especially the slides. People were saying that they clean the part, work this stuff into the part and let it sit. Then clean off the part. Its supposed to revive the parts and make them more pliable.
I went out and bought a tube for 8 bucks. Used it on my in-laws brake job and it worked well. I then put it on my rear axle rebound bumpers and rocker drain flaps in front of the rear wheels. All these parts were off the vehicle already. I cleaned the parts and then worked the Sil-glide into the part and left extra on it. Then I put the parts in a small zip lock back and let it sit a couple days. Went back to them, work the stuff into the parts some more and let it sit. Well after a couple of days I removed the part, wiped it clean and it looked good as new. I have to say it was a little more pliable than when I started. Not that the rebound bumpers are that pliable to begin with. But the rocker drain flaps were much better.
I've seen other guys using Sil-glide on there trunk and door weather stripping. I'll be trying that next during assembly.
This has me thinking about doing my dash pad.
Just thought I'd post up my findings with this stuff. Heres a link at advance auto. I know napa carries it too.
http://shop.advanceautoparts.com/p/american-grease-stick-co.-sil-glyde-silicone-brake-lubricant-tube-4-oz-bk-4/12024852-p?iv_=__iv_p_1_a_214327102_g_12425515822_w_pla-191564126422_h_9004189_ii__d_c_v__n_g_x_pla_y_6201684_f_online_o_12024852-P_z_US_i_en_j_191564126422_s__vi__&utm_source=ACQ&utm_medium=cpc&utm_campaign=PLA&utm_content=shoppingcampaigns&gclid=CJz_4IXswdACFQlXDQodj-cMrA
Joe73- Donating Member
- Street Cred : 83
Re: Rubber parts conditioner
Joe can this be used After a Dash has been dyed as In My case I am dying it to red from Blue or will it take the Dye out ??
___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE- Management
- Street Cred : 98
Re: Rubber parts conditioner
My thoughts about this being effective on vinyl that's been "dyed" is that the term "dye" is a misnomer meaning nothing more than applying a compatible paint...in which case, would seal any pores that would normally absorb a conditioner such as this.
Mcarlo77- Donating Member
- Street Cred : 78
Re: Rubber parts conditioner
Im not sure.but I would think not. But it may work since.the.is.not a paint. Paint would seal a surface and nothing should.penetrate.
Joe73- Donating Member
- Street Cred : 83
Re: Rubber parts conditioner
I would consider.a.the.more.like a stain. It has the.ability to change a color but not "coat" the.surface with a.layer. The.soaks in like on seat belts. Paint on seat belts.would.become.stiff.
That why I like to sgain wood because.it can still breathe. Painting. Wood eventually peels.
That why I like to sgain wood because.it can still breathe. Painting. Wood eventually peels.
Joe73- Donating Member
- Street Cred : 83
Permissions in this forum:
You cannot reply to topics in this forum
Thu Dec 05, 2024 10:41 am by zucchi
» I have posted on here for info and help
Thu Dec 05, 2024 12:11 am by muldokken
» Roll Call and Car showcase
Fri Nov 29, 2024 5:24 pm by 76Chevelle2Tone
» Happy Thanksgiving 2024
Thu Nov 28, 2024 12:21 pm by Limey SE
» Life & Back On The Radio
Thu Nov 28, 2024 1:46 am by knightfan26917
» Monte Carlo -75
Wed Nov 27, 2024 12:57 pm by Finn Monte
» 1974 Pontiac Grand Prix
Mon Nov 25, 2024 5:06 pm by Iggy
» Ads
Mon Nov 25, 2024 12:52 am by 76Chevelle2Tone
» 1975 El Camino - long term project
Sun Nov 24, 2024 8:33 pm by tgaetto
» station wagon tailgate release
Sat Nov 23, 2024 8:28 pm by bucket